ICSAM 2009 Technical Program - Preliminary |
|
Location: Bell Harbor Center, Seattle, Washington, U.S.A. |
|
Monday (June 29) - Morning |
|
| 8:30 AM - 12:30 PM |
Boeing Plant Tour: Bus to and from Everett - Wide Body Aircraft Manufacturing Facilities. Reservations were requested, but some seats are still available, cost is $17.50 per person. Fee collected on the bus. |
Monday (June 29) - Afternoon |
|
| 3:00-8:00 PM | Registration |
| 5:00-7:00 PM | Opening Reception |
Tuesday (June 30) - Morning |
|
| 7:15-8:15 AM | Contenental Breakfast & Coffee |
Opening Plenary: Special Topics in Superplasticity and Superplastic Forming |
|
| 8:15-8:30 AM | Opening Remarks - Daniel Sanders |
| 8:30 AM | Richard Todd |
| 9:00 AM | Terance Langdon |
| 9:30 AM | Break |
| 10:00 AM | Marwan Khraisheh |
| 10:30 AM | Amiya Mukherjee |
| 11:00 AM | Gerard Bernhart |
| 11:30 AM | Eric Taleff |
| 12:00-1:00 PM | Lunch |
Tuesday (June 30) - Afternoon |
|
Technical Sessions |
|
| 1:00-5:00 PM | Session 1A: Industrial Applications and Innovations (a) |
| 1:00-5:00 PM | Session 2A: Material Processing Methods to Enhance Superplasticity (a) |
| 1:00-5:00 PM | Session 3A: Numerical Simulations and Modeling (a) |
| 5:00-6:30 PM | POSTER SESSION |
| 6:30-8:30 PM | ICSAM Org. Board Meeting |
Wednesday (July 1) - Morning |
|
Technical Sessions |
|
| 8:00AM -12:00 PM | Session 1B: Industrial Applications and Innovations (b) |
| 8:00AM -12:00 PM | Session 2B: Superplasticity in Metal Alloys (a) |
| 8:00AM -12:00 PM | Session 3B: Numerical Simulations and Modeling (b) |
| 12:0-1:00 PM | Lunch |
Wednesday (July 1) - Afternoon |
|
Technical Sessions |
|
| 1:00-5:00 PM | Session 1C: Microstructure Control & Evolution, Mechanisms of Grain Boundary Sliding and Failure |
| 1:00-5:00 PM | Session 2C: Material Processing Methods to Enhance Superplasticity (b) |
| 1:00-5:00 PM | Session 3C: Superplasticity in Ceramics, Intermetallics, Bulk Metallic Glasses and Nanomaterials |
| 7:00-10:00 PM |
Conference Dinner Cruise |
Thursday (July 2) - Morning |
|
Technical Sessions |
|
| 8:00 AM - 12:00 PM | Session 1D: Industrial Applications and Innovations (c) |
| 8:00 AM - 12:00 PM | Session 2D: Material Processing Methods to Enhance Superplasticity (c) and Superplasticity in Metal Alloys (b) |
| 8:00 AM - 12:00 PM | Session 3D: High Strain Rate and Low Temperature Superplasticity |
| 12:00 - 1:00 PM | Lunch |
Thursday (July 2) - Afternoon |
|
Closing Plenary: Special Topics in Superplasticity and Superplastic Forming |
|
| 1:00 PM | Werner Beck |
| 1:30 PM | A.J. Barnes |
| 2:00 PM | Richard Curtis |
| 2:30 PM | Break |
| 3:00 PM | Koichi Kitazono |
| 3:30 PM | Paul Krejewski |
| 4:00-4:45 PM | Panel Discussion: Werner Beck, A.J. Barnes, Gerard Bernhart, Ruslan Valiev, Paul Krejewski |
| 4:45-5:00 PM | Larry Hefti, ICSAM 2009 Deputy Chair |
